3306 DIRECT INJECTION VEHICULAR ENGINE WITH NEW SCROLL FUEL – Governor Control

D7G With Power Shift Transmission

Tighten locknuts (A) on rod ends to … 12 ± 4 N·m (9 ± 3 lb ft)

With governor at High Idle, install lever (B) on governor shaft at an angle from vertical of … 20 ± 5°

Dimension (C) approximately … 438.0 mm (17.25 in)

Dimension (D) approximately … 597.0 mm (23.50 in)

Dimension (E) approximately … 610.0 mm (24.00 in)

Dimension (F) approximately … 100.00 mm (3.94 in)

Dimension (G) … 1.5 mm (.06 in)

Adjust bolt (H) to get dimension (F) with engine at High Idle

Adjust setscrew (J) so that engine speed is 985 ± 50 rpm with decelerator pedal depressed. Check High Idle speed after adjustment.

After linkage has been adjusted, move control lever to High Idle and adjust setscrew (K) to get dimension (G).

D7G With Direct Drive Transmission & 571G Pipelayer

Tighten locknuts (A) on ends to … 12 ± 4 N·m (9 ± 3 lb ft)

With governor at High Idle, install lever (B) on governor shaft at an angle from vertical of … 20 ± 5°

Dimension (C) approximately … 438.0 mm (17.25 in)

Dimension (D) approximately … 597.0 mm (23.50 in)

572G Pipelayer

Tighten locknuts (A) on rod ends to … 12 ± 4 N·m (9 ± 3 lb ft)

With governor at High Idle, install lever (B) on governor shaft at an angle from vertical of … 5° ± 5°

Dimension (C) approximately … 726.4 mm (28.6 in)

Dimension (D) approximately … 683.3 mm (26.9 in)

7G5554 Control Group (D6H)

1. Tighten locknuts (A) on rod ends to … 14 ± 4 N·m (10 ± 3 lb ft)

2. Align the timing mark on shaft (B) with centerline of sawcut on lever (C).

3. Dimension (D) approximately … 508 mm (20 in)

4. With governor control lever in a vertical position, angle (E) … 32° ± 5°

3T4347 Control Group (D6H)

1. Tighten locknuts (A) on rod ends to … 14 ± 4 N·m (10 ± 3 lb ft)

2. Align the timing mark on shaft (B) with centerline of sawcut on lever (C).

3. Dimension (D) approximately … 508 mm (20 in)

4. With governor control lever in a vertical position, angle (E) … 32° ± 5°

6T3303 Control Group (D7H)

1. Tighten locknuts (A) on rod ends to … 12 ± 4 N·m (9 ± 3 lb ft)

2. Align the timing mark on shaft (B) with centerline of sawcut on lever (C).

3. With governor control lever in a vertical position, angle (E) … 32° ± 5°

8P3126 Control Group (D5B SA)

1. With control lever (1) in high idle position

Dimension (A) approximately … 495.0 mm (19.5 in)

Dimension (B) approximately … 786.0 mm (30.9 in)

Angle (C) from vertical … 10° ± 5°

2. Tighten locknuts (2) on rod ends to … 25 ± 7 N·m (18 ± 5 lb ft)

3. Tighten locknuts (3) on rod ends to … 12 ± 4 N·m (9 ± 3 lb ft)

9W3764 Control Group (D6D SA)

1. With control lever (1) in high idle position

Dimension (A) approximately … 495.0 ± 3.0 mm (19.5 ± .1 in)

Dimension (B) approximately … 735.0 mm (28.9 in)

Angle (C) from vertical … 19° ± 5°

2. Tighten locknuts (2) on rod ends to … 14 ± 4 N·m (10 ± 3 lb ft)

3. Tighten locknuts (3) on rod ends to … 14 ± 4 N·m (10 ± 3 lb ft)

8V2049 Governor Control Group (Challenger 65)

With governor lever (1) pushed full forward

Dimension (A) … 233.0 ± 1.5 mm (9.17 ± .06 in)

Angle (B) from horizontal … 22.5 ± 1.0°

Posted in D6Tagged